top of page

/Hamilton, ON

HAMILTON, ON · ONTARIO, CANADA

Corner commercial building on Kensington Avenue in Hamilton, Ontario, in winter, documented by ADS

KENSINGTON AVENUE BUILDING · 5,339 SQ FT · DOCUMENTED 2025

As-Built Drawings in Hamilton, ON

ADS provides as-built drawings and 3D laser scanning in Hamilton, Ontario. In early 2025 our team documented a 5,339 sq ft three-level commercial building on Kensington Avenue with a Matterport Pro3, delivering a point cloud, a 360° walkthrough and an LOD 300 Revit model with custom families for its historic windows and facade details.

✓

Itemized quote, travel shown up front

✓

You own every file

✓

Your building stays in use

OUR WORK IN HAMILTON · READ AS A BUILDING SECTION

Three levels, scanned in sequence and tied into one model

The building sits on a prominent corner lot and spans a basement, a ground floor and a mezzanine. ADS was commissioned to produce a full as-built BIM model ahead of renovations and detailed retail planning.

5,339 SQ FT ACROSS THREE LEVELS

EXTERIOR

The same scanner captured the outside of the building: ornamental facades and distinctive window designs on a corner lot.

LEVEL 3

TOP OF THREE

Mezzanine

The top of the stack. It was scanned in sequence with the floor below, with enough overlap for the two levels to register as one building.

CAPTURED

High-density point cloud, Matterport Pro3

TIED TO

Ground floor, by overlapping scans

MODELLED

LOD 300 Revit

OVERLAP · FLOOR TRANSITION

LEVEL 2

MIDDLE OF THREE

Ground floor

The middle of the stack, and the link between the other two. Overlapping scans connect it up to the mezzanine and down to the basement.

CAPTURED

High-density point cloud, Matterport Pro3

TIED TO

Mezzanine above, basement below

MODELLED

LOD 300 Revit

OVERLAP · FLOOR TRANSITION

LEVEL 1

LOWEST OF THREE

Basement

The bottom of the stack. Overlap with the ground floor carries the alignment down, so the basement sits correctly under the rest of the model.

CAPTURED

High-density point cloud, Matterport Pro3

TIED TO

Ground floor, by overlapping scans

MODELLED

LOD 300 Revit

Section views of the Kensington Avenue building model

THE SAME STACK, IN THE MODEL

Section views cut through the finished Revit model.

PROJECT

Teatrix Costume Store

DATES

Feb 26–Mar 7, 2025

SIZE

5,339 sq ft

CAPTURE

Matterport Pro3

WHAT MADE IT HARD

A shop full of stock, behind a historic facade

Scanning around the inventory

The store was fully stocked. The crew worked around on-site materials and inventory with angled capture, then aligned the scans carefully in post-processing.

Historic details as custom Revit families

Architectural mouldings, asymmetrical facades and custom window profiles were modelled with tailored Revit components. The LOD 300 model includes custom families for the historic windows, built-ins and facade elements.

WHAT WAS DELIVERED

01

High-density point cloud of all levels

02

Matterport 360° walkthrough

03

LOD 300 Revit model of the full building

Interior views of the Kensington Avenue building in Hamilton

Interiors, as captured

Revit views of the Kensington Avenue building model

Revit views of the model

Exterior and interior model views of the Kensington Avenue building

Model views, outside and in

3D model views of the Kensington Avenue building

3D views for online review

04

Custom Revit families for historic windows, built-ins and facade elements

05

3D online visualization model and views

3D model of the Kensington Avenue building in Hamilton

The whole building as an LOD 300 Revit model

“Always delivers exactly what we need, when we need it.”

Basel Alhatabeh

Manager, HKA

WHAT YOU CAN ORDER

Order one layer, or the whole set

Every job starts with a registered point cloud from our 3D laser scanning. It is the raw measured record of the building, and teams that model in-house sometimes need nothing more.

Most renovation teams add 2D CAD as-builts through our as-built services: floor plans, reflected ceiling plans, elevations and sections in AutoCAD and PDF. Consultants who work in BIM order a Revit model at LOD 200–300, built from the scan by our scan to BIM team.

Where it is in scope, MEP documentation records exposed mechanical, electrical and plumbing. Building site plans cover roofs and sites, drawn from aerial or ground capture where the project calls for them. Building surveys add BOMA area figures for leasing and asset records, on request.

Every quote is itemized, so you pay for the formats you need and nothing else.

Drawing sheets and model views of the Kensington Avenue building

Sheets and views produced from the model

FILE FORMATS YOU RECEIVE

DRAWINGS

DWG, PDF

BIM MODEL

RVT, IFC, NWC

POINT CLOUD

E57

WALKTHROUGH

Matterport

FOUR STEPS UP

How a Hamilton project runs

STEP 1

Send the basics

The address, approximate square footage and the deliverables you need.

STEP 2

Get an itemized quote

Each deliverable is its own line, and so is travel.

STEP 3

Scan day

Each level is scanned in sequence with overlap so the floors register cleanly. The shop stays open.

STEP 4

Review and delivery

Drawings are drafted from the point cloud. You review the set before final delivery.

PERMITS AND REVIEW IN HAMILTON

On a designated property, the Heritage Permit comes first

Your architect files the application. If the building is designated, heritage approval comes first.

IF

The property is designated, or sits inside a Heritage Conservation District

Exterior work on a property inside a district also needs a Heritage Permit.

FIRST

Heritage Permit

The owner of a designated property needs a Heritage Permit before altering features that could affect its heritage attributes.

THEN

Building permit

The City of Hamilton Building Division issues building permits under Ontario’s Building Code Act.

The City will not issue a building permit until the Heritage Permit is approved.

WHERE WE WORK

Hamilton, Dundas, Ancaster, Stoney Creek, Burlington, Oakville and Mississauga.

QUESTIONS

Hamilton questions, stacked

Something else? Call 1-855-201-4043 and ask a specialist.

−

Can you model historic facade details?

Yes. For the Kensington Avenue building in Hamilton, ADS built an LOD 300 Revit model with custom families for the historic windows, built-ins, mouldings and asymmetrical facade elements.

−

Can you scan a shop that is full of stock?

Yes. The Hamilton store was fully stocked. The crew navigated on-site materials and inventory using angled capture and careful alignment during post-processing.

−

Do I need a heritage permit before a building permit in Hamilton?

If the property is designated, yes. The City of Hamilton requires an approved Heritage Permit before altering heritage attributes and will not issue a building permit until it is in place.

−

Do you work elsewhere in Canada?

Yes. ADS has also documented the MacMillan Theatre at the University of Toronto and, in the Montreal area, Douglas Hospital and a secondary school.

−

Does the business have to close while you scan?

No. Scanning is non-contact, so the shop stays open. Each level is scanned in sequence.

GET A QUOTE

Tell us about your Hamilton property

Four details are enough for us to price it. Existing drawings help us scope faster, even old ones.

PREFER TO TALK?

Request an itemized quote

Send the property address, approximate square footage, the deliverables you need and your deadline. We reply with an itemized quote.

Itemized quote, one line per deliverable

Scanned by the team behind the Kensington Avenue project

CAD, PDF, Revit and point cloud files are yours to keep

BEYOND HAMILTON

More ADS projects in Canada

ADS has also documented the MacMillan Theatre at the University of Toronto and, in the Montreal area, Douglas Hospital and a secondary school.

MacMillan Theatre, University of Toronto, documented by ADS
Douglas Hospital, documented by ADS

MORE CANADA & INTERNATIONAL CITY PAGES

·

·

Pointe-aux-Trembles Secondary School, documented by ADS

MEMBERSHIPS

ICSC member
Broward County Chamber of Commerce member
Chamber Approved A+
South Florida Women's Chamber of Commerce member

Reviewed by Antonio Tomecich

Founder & Director, As-Built Drawing Services.

Last reviewed November 2026.

bottom of page