BALTIMORE, MD · BALTIMORE CITY
As-Built Drawings in Baltimore, MD
ADS (As-Built Drawing Services) captures buildings with LiDAR and drafts as-built drawings from the scan. In Baltimore we documented a three-story, 5,069 sq ft rowhouse on Pratt Street, with its basement and rooftop terrace, between January 10 and 13, 2025. The point cloud, digital twin and annotated AutoCAD and PDF drawings were delivered in three days.
✓
Travel is its own line on the quote
✓
You own every file
✓
Your home stays in use

PRATT STREET ROWHOUSE · 5,069 SQ FT · JAN 2025
READ THIS PAGE LIKE A SECTION DRAWING
The Pratt Street rowhouse, floor by floor
A rowhouse is a stack of narrow floors between two party walls. This page is laid out the same way. Start on the roof terrace and work down to the basement.
R
3
2
1
B
ROOF TERRACE · OVERVIEW
The house in brief
The house stands in East Baltimore's historic Pratt Street corridor. It keeps the narrow proportions typical of the area, and the interior was being modernized when we arrived. ADS surveyed every level and modeled it to produce the as-built record for the renovation and the design work that follows.
LEVELS
Three stories, a basement and a rooftop terrace
FLOOR AREA
Approximately 5,069 sq ft
SCANNED
January 10 to 13, 2025
DRAWINGS
Delivered three days later
USED FOR
A modern kitchen and an addition designed into the historic shell
THIRD FLOOR · WHAT WAS MEASURED
What the scan recorded that a tape would miss
Nineteenth-century masonry houses settle. Walls are rarely plumb and floors are rarely level, and a tape survey assumes right angles that are not there. The LiDAR scan recorded the geometry as it stands.
The thickness of the party walls
The slope of the floor joists
The position of the chimney flues
Roof slopes and ceiling heights, including where they vary
Doors, windows and fixed furniture, cataloged level by level
Openings, built-ins and partitions, checked for alignment

One floor in the scan data, with dimensions taken from the point cloud.
SECOND FLOOR · DRAWINGS AND FILES
What was delivered, and what you can order
The basement, the main floors and the rooftop terrace were all rebuilt from one LiDAR dataset and cross-checked, so the stacked levels stay in register with each other.
DELIVERED ON PRATT STREET
High-resolution LiDAR point cloud
360° digital twin for remote viewing
Floor plans, elevations, reflected ceiling plans and structural sections
AutoCAD drawings and annotated PDF sheets

The basement and first floor plans. The house is long and narrow on every level.
ON YOUR QUOTE, LINE BY LINE
A registered point cloud and digital twin from 3D laser scanning.
2D CAD in AutoCAD and PDF through our as-built services.
A Revit model at LOD 200 to 300 from BIM services, when you need BIM.
MEP documentation and structural elements, when they are in scope.
Building site plans for the lot, the yard and an addition.
BOMA or REBNY area calculations on request, part of our building surveys.
DWG
RVT
IFC
NWC
E57
Matterport
FIRST FLOOR · THE FRONT DOOR
Permits and historic review in Baltimore
Your architect or engineer files the application. Our drawings are the existing-conditions base inside it.
Department of Housing & Community Development, Permits Office
417 E. Fayette Street, Room 100
443-984-1809 · applications through the E-Permits portal
The Permits Office issues building permits in Baltimore City for constructing, enlarging, altering, repairing or rehabilitating any structure, inside or out.
Historic district or landmark? CHAP comes first. Exterior work in a local historic district or on a designated landmark needs an Authorization to Proceed from the Commission for Historical and Architectural Preservation (CHAP) before a building permit is issued. A permit application filed before that review is put on hold until CHAP is finished. Measured facade elevations make that step faster.

The exterior as modeled, with three stories of window openings.
BASEMENT · QUESTIONS
Baltimore FAQ
Can you document a historic rowhouse that is mid-renovation?
−
Yes. The Pratt Street house was documented while its interior was being modernized, and the record showed party-wall thickness, joist slope and flue positions that no earlier drawings had.
Will the drawings work for a Baltimore City permit?
−
Yes. They are prepared as the existing-conditions base for the application your architect or engineer files with the Baltimore City Department of Housing and Community Development. Its Permits Office at 417 E. Fayette Street, Room 100, issues permits through the E-Permits portal.
When does a project need a CHAP Authorization to Proceed?
−
Exterior work needs one first if the property is in one of the city's local historic districts or is a designated landmark. It comes from the Commission for Historical and Architectural Preservation (CHAP). A permit application filed before that review is placed on hold until CHAP is finished. Measured facade elevations make that step faster.
How accurate is a survey of a house that has settled?
−
The drawings show the house as it is, lean included. ADS scans with Leica RTC360, Leica BLK2GO and Matterport Pro3 units and drafts from the point cloud, so uneven joists and out-of-square rooms appear as they are. That keeps cabinetry, flooring and new steel from being modified on site.
Is it worth bringing ADS to Baltimore from out of town?
−
Yes, for most jobs. Travel is a single visible line on the quote, and a rowhouse is scanned in one visit: the Pratt Street house was captured over four days in January and the drawings followed in three days. If a project is too small to carry the trip, ADS will say so.
Does the house have to be empty during the scan?
−
No. Scanning is non-contact, so a home, office or store stays in use. ADS can schedule around tenants or trades already working.

CUT THROUGH EVERY LEVEL
LEVEL
“Quick delivery in three days with clear, proactive coordination.”
The as-builts were delivered in three days, exactly as expected.
Alina Hackett, Interior Designer at Leyden Lewis Design Studio
STREET LEVEL · GET A QUOTE
Tell us about your Baltimore property
Send the address, the approximate square footage, the number of floors and the deliverables you want. ADS has no Baltimore office, so travel appears as its own line. Existing drawings help us scope faster, even old ones.
WHERE WE WORK
Downtown and the Inner Harbor, Fells Point, Canton, Federal Hill, Mount Vernon, Bolton Hill, Hampden, Charles Village and Highlandtown, plus Towson, Catonsville, Columbia, Ellicott City and Annapolis.
MORE ADS CITY PAGES
FURTHER NORTH
The 565,308 sq ft Poughkeepsie State Office Building and a 2,500 sq ft SoHo office suite in Manhattan.
MEMBERSHIPS




Reviewed by Antonio Tomecich
Founder & Director, As-Built Drawing Services.
Last reviewed November 2026.