CHARLOTTE, NC · MECKLENBURG COUNTY

GALLERY HOUSE · 10,443 SQ FT · FEB 2025
As-Built Drawings in Charlotte, NC
ADS (As-Built Drawing Services) documents existing buildings with LiDAR and delivers the drawings and models design teams use. In Charlotte we surveyed the 10,443 sq ft Gallery House, a three-level art and gathering space in the North Tryon arts district, in February 2025 and delivered a point cloud, an LOD 300 Revit model, a photo record and a virtual walkthrough.
✓
Travel shown as its own line
✓
You own every file
✓
Your building stays open
OUR WORK IN CHARLOTTE
The Gallery House survey, hung as a wall
The building shows art, so we have hung the survey the same way. Photographs sit next to the point cloud and the model that were built from them. The plaque carries the facts.

01
The bar, photographed during the survey. Paintings hang on the wall opposite the counter.

02
The scan data seen from above, before any drafting.

04
The high-density point cloud: the levels stacked, then one level in plan.

05
The lounge from the other end. Gathering space and exhibition space share one room.
PROJECT RECORD · ADS
Gallery House
LiDAR survey and BIM documentation for renovation planning
WHERE
North Tryon arts district, Uptown Charlotte
SIZE
10,443 sq ft on three levels
USE
Art exhibitions and gatherings, part cultural and part commercial
SURVEYED
February 10 to 17, 2025
MODEL
LOD 300 Revit, existing conditions

07
The bar again, from the far end.

03
A corridor in the model of existing conditions.

06
Walls, openings and ceilings modeled from the scan.

08
The building in the modeling software: massing, scan and drawn plans side by side.
WHAT WAS DELIVERED
Four pieces came off the scan
The renovation planners needed an accurate architectural base for a property that mixes commercial and exhibition space. The interiors were scanned at high resolution, and the facade and roof were worked up in CAD.
A
High-density point cloud
The measured record of all three levels.
B
Photo record
Interior and exterior photographs taken with the survey.
C
LOD 300 Revit model
Existing conditions, with spatial and structural components.
D
Virtual walkthrough
An interactive tour the team can open without visiting.
HYBRID LAYOUT
Where shop becomes gallery
The model follows each transition between the commercial rooms and the exhibition rooms, so neither is drawn as a generic box.
REFLECTIVE FINISHES
Light that confuses a scanner
Lighting interference was handled on site by adjusting how and where each scan was taken.
FACADE DETAILING
A front that has to be right
The facade was modeled with extra precision, because compliance review and the renovation design both depend on it.
“Fast and professional service with outstanding results.”
The model looks great, and we truly appreciate the team's effort throughout the process. Their fast and professional service ensured we received precisely the information we needed to move forward with confidence.
CAMERON BARRADALE · STUDIO DIRECTOR AT GENSLER
WHAT YOU CAN ORDER
The catalogue for a Charlotte building
A typical package starts with the point cloud and adds the drawings or model your team works in. Every item is its own line on the quote.
No. 1
DWG
No. 2
No. 3
RVT
No. 4
IFC
No. 1
Registered 3D point cloud. Captured by 3D laser scanning, with a 360° digital twin that lets everyone on the project walk the building from a browser.
No. 2
2D CAD set. Floor plans, reflected ceiling plans, elevations and sections in AutoCAD and PDF from our as-built services.
No. 3
Revit model. LOD 200 to 300 for BIM-based teams, built through BIM services.
No. 4
MEP and structure. Picked up when scoped. See MEP documentation.
No. 5
NWC
No. 6
E57
No. 7
Matterport
No. 5
Site plan. The building on its lot, drawn as a building site plan.
No. 6
Area calculations. BOMA or REBNY figures for leasing and valuation, part of our building surveys.
PERMITS AND REVIEW
Two offices review a Charlotte project
FIRST, WHERE IT APPLIES
City of Charlotte
Zoning and site approval stay with the city.
Commercial projects that need city site approval get it before the county issues the building permit.
WHERE WE WORK
Uptown, South End, Dilworth, Myers Park, SouthPark, Ballantyne, NoDa, Plaza Midwood, University City, Matthews, Mint Hill, Pineville, Huntersville, Cornelius, Davidson, Fort Mill and Rock Hill.
THEN THE BUILDING PERMIT
Mecklenburg County Code Enforcement
A division of the county's Land Use and Environmental Services Agency, at 2145 Suttle Avenue. It issues building permits for Charlotte and for the county's towns: Cornelius, Davidson, Huntersville, Matthews, Mint Hill and Pineville. See code.mecknc.gov.
Your architect or engineer files. The ADS set is the existing-conditions base.
ALSO IN THE SOUTHEAST
Related projects: the 9,110 sq ft single-family home in Banner Elk (2024) and the 5,132 sq ft Fendi boutique at Phipps Plaza in Atlanta (2022).
QUESTIONS
Charlotte FAQ
Who issues building permits in Charlotte?
Mecklenburg County Code Enforcement issues building permits in Charlotte. It is a division of the county's Land Use and Environmental Services Agency and also serves Cornelius, Davidson, Huntersville, Matthews, Mint Hill and Pineville. Zoning and site approval stay with the City of Charlotte. Your architect or engineer uses the ADS set as the existing-conditions base for the submittal.
Do you document large houses as well as commercial buildings?
Yes. The Gallery House in Charlotte is 10,443 sq ft of commercial space, and the Banner Elk home ADS documented in 2024 is 9,110 sq ft. The workflow is the same and only the drawing list changes.
How do you scan glass and reflective finishes?
Scanner settings are adjusted on site for difficult surfaces such as glass curtain wall and polished floors. ADS uses Leica RTC360 and BLK2GO scanners and the Matterport Pro3, and every dimension in the drawings is taken from the point cloud.
Is it worth bringing ADS in from outside Charlotte?
For most jobs, yes. The travel line is small next to the drafting, the scan is a single trip, and everything afterwards is produced from the point cloud, so you never pay for a return visit to re-measure.
Does the building have to close during the scan?
No. Offices, shops and homes stay in use while ADS scans. The crew can work early, late or at weekends if that suits the tenant.
What drives the cost of an as-built survey in Charlotte?
Four things drive the price: floor area, how much is in the building, the deliverables you pick and travel. Point cloud with 2D floor plans is the entry tier, and a full CAD set and a Revit model add drafting hours. Quotes are itemized line by line.
GET A QUOTE
Tell us about your Charlotte building
MEMBERSHIPS




Reviewed by Antonio Tomecich
Founder & Director, As-Built Drawing Services.
Last reviewed November 2026.