top of page

/Los Alamos, NM

LOS ALAMOS, NM · LOS ALAMOS COUNTY

Stone-walled single-family home in Los Alamos, New Mexico, with a large sloped glazed roof, seen from the driveway

LOS ALAMOS HOME · 5,922 SQ FT · JULY 2024

As-Built Drawings in Los Alamos, NM

ADS turns LiDAR scans into as-built drawings for owners and architects in Los Alamos, New Mexico. In July 2024 our team surveyed a 5,922 sq ft custom home, facade and interior, ahead of renovations, and delivered a point cloud, georeferenced orthophotos, 2D CAD floor and ceiling plans, an LOD 300 Revit model and a Matterport twin.

✓

Travel shown as its own line

✓

You own every file

✓

Your building stays in use

OUR WORK IN LOS ALAMOS

One survey, both sides of the wall

This custom residence needed drawings to renovate from without losing the original design. So the survey covered the house twice over: the facade as it stands, and every room behind it. Below, the same job is laid out the way it was captured. Outside on the left. Inside on the right.

BUILDING

Custom single-family residence

SIZE

5,922 sq ft

DATES

July 2 to July 12, 2024

CAPTURE

Terrestrial LiDAR scanning

PURPOSE

Future renovations that keep the original design

OUTSIDE

The facade, recorded before anything changes

3D model of the two-storey facade of the Los Alamos home, with balcony, exterior stair, doors and windows highlighted

EXTERIOR OF THE MODEL, OPENINGS HIGHLIGHTED

Renovating a house without spoiling it starts with knowing exactly what is there. The exterior was scanned from the ground so the original design is on record before any work is planned: wall lines, roof slope, openings, balcony and stair.

DELIVERED FOR THE OUTSIDE

High-density LiDAR point cloud

The facade measured as it stands.

Georeferenced orthophotos

Reference images for facade updates.

LOD 300 Revit model, exterior

Existing building conditions, ready for design.

Point cloud view of the Los Alamos home exterior with its glazed roof and the trees around it

POINT CLOUD OF THE HOUSE AND TREES

EXTERIOR WALL

INSIDE

Floors and ceilings that change from room to room

Plan view of the interior point cloud of the Los Alamos home, showing room layouts and floor finishes

INTERIOR POINT CLOUD, CUT AT PLAN LEVEL

Inside, the difficulty was the geometry. Floor and ceiling layouts in this house are complex, so they were worked out in BIM and CAD together. The floor plans, the ceiling plans and the Revit model all come from the same scan data.

DELIVERED FOR THE INSIDE

2D CAD floor and ceiling plans

Drawn for renovation planning.

Georeferenced orthophotos

Reference images for interior updates.

LOD 300 Revit model, interior

The same model, room by room.

Matterport virtual twin

Hosted so everyone involved could review the house remotely.

Revit screen showing a floor plan, an elevation and the 3D model of the Los Alamos home

PLAN, ELEVATION AND MODEL IN REVIT

WHERE THE TWO SIDES MEET

The section shows inside and outside at once

As-built section through the Los Alamos home showing the sloped roof, two floor levels and an exterior stair

SECTION THROUGH THE SLOPED ROOF

Cut the model through and the two halves of the survey line up on one sheet: roof slope and ground line from outside, floor levels and ceiling heights from inside. This is the check that the facade record and the room record describe the same house.

As-built section through the Los Alamos home with labelled living room, bedroom, bath, corridor and garage

SECTION THROUGH LIVING ROOM, BEDROOM AND GARAGE

FROM THE OWNER

The team delivered precise, high-quality scans and digital models that gave us everything we needed to move forward with confidence.

Their communication was clear, their turnaround was fast, and the final results exceeded expectations. I’d gladly work with them again.

ERICK TALLEY · HOMEOWNER, LOS ALAMOS, NM

WHAT YOU CAN ORDER

Order one side, the other, or both

Not every project needs the whole house. A facade repair needs the outside. A kitchen remodel needs the inside. Each item is its own line on the quote, so you can drop what you do not need.

FILE FORMATS DWG · PDF · RVT · IFC · NWC · E57 · Matterport

PERMITS AND REVIEW

Two permit desks: the County and the State

BUILDING PERMITS

Incorporated County of Los Alamos Community Development Department

Building permits for Los Alamos County are applied for through the Citizen Self-Service portal. The department has set a goal of processing residential permits in 3 days or less and commercial permits in 5 days or less, on average.

ELECTRICAL, MECHANICAL AND PLUMBING PERMITS

State of New Mexico (CID)

Trade permits are issued by the State, not the County. Work on wiring, ductwork or piping goes to a different desk than the building permit.

WHO FILES

Your design professional files the application. We make sure the existing conditions in it are right.

WHERE WE WORK

Los Alamos townsite, White Rock, and the drive down the hill to Pojoaque, Española, Santa Fe and Taos.

QUESTIONS

Los Alamos questions

Have you scanned a home in Los Alamos before?

Yes. In July 2024 ADS documented a 5,922 sq ft single-family home in Los Alamos with terrestrial LiDAR. The deliverables were a point cloud, georeferenced orthophotos, 2D CAD floor and ceiling plans, an LOD 300 Revit model and a Matterport twin.

Do you document the outside of a house as well as the inside?

Yes. The Los Alamos survey captured both facade and interior details in one LiDAR survey. Orthophotos were delivered as reference for facade and interior updates, and the Revit model represents the existing building conditions.

Who issues building permits in Los Alamos?

The Incorporated County of Los Alamos Community Development Department issues building permits, and applications go through its Citizen Self-Service portal. Electrical, mechanical and plumbing permits are issued by the State of New Mexico (CID), not the County. Your architect or engineer files the application with our drawings as the existing-conditions base.

Is it worth bringing ADS to Los Alamos from out of town?

One trip normally covers the capture, and travel is a separate line on the quote because we have no New Mexico office. Registration, drafting and modelling are done remotely afterwards. The Los Alamos home, the Amarillo dealership and the Scottsdale store were all handled this way.

What sets the cost of an as-built survey in Los Alamos?

Floor area, how complex the building is, the deliverables you choose and travel set the price. A simple rectangular plan drafts faster than a split-level home with varied ceilings. Point cloud plus 2D CAD is the base tier, and a Revit model adds modelling time.

Does the house have to be empty while you scan?

No. A technician works through the space while it is occupied. The scans are then registered into one point cloud, and the drawings and model are drafted from it.

Request an itemized quote

Send the property address, approximate square footage, the deliverables you need and your deadline. We reply with an itemized quote.

GET A QUOTE

How a Los Alamos project runs

01

Send the basics

The address, approximate square footage and number of floors, and the deliverables you need.

02

Get an itemized quote

Travel is its own line, since we have no New Mexico crew.

03

Scan day

A technician works through the building while it stays in use.

04

Review and delivery

The scans are registered into one point cloud and the set is drafted from it. You review it and request revisions before final delivery.

PREFER TO TALK?

MEMBERSHIPS

ICSC member
Broward County Chamber of Commerce member
Chamber Approved A+
South Florida Women's Chamber of Commerce member

Reviewed by Antonio Tomecich

Founder & Director, As-Built Drawing Services.

Last reviewed November 2026.

bottom of page