top of page

/Fort Myers, FL

FORT MYERS, FL · LEE COUNTY

As-Built Drawings in Fort Myers, FL

ADS produces as-built drawings in Fort Myers, Florida from LiDAR scans. In April 2024 our team scanned the interior of the 13,065 sq ft Surf Style store on Estero Boulevard in Fort Myers Beach after Hurricane Ian, and delivered a point cloud, a 360° walkthrough, plans, sections and an LOD 200 Revit model for the redesign.

Surf Style store in Fort Myers Beach with its turquoise beach chair sign out front

SURF STYLE STORE · 13,065 SQ FT · SCANNED 2024

✓

Travel shown as its own quote line

✓

You own every file

✓

Your property stays open

OUR FORT MYERS PROJECT

Surf Style store, Fort Myers Beach

WHERE

Estero Boulevard, Fort Myers Beach, Florida

BUILDING

13,065 sq ft retail store

PROJECT DATES

April 8 to 21, 2024

WHY IT WAS SCANNED

Structural assessment and redesign after Hurricane Ian in 2022

WHAT WAS CAPTURED

Wall layouts, ceiling structure, floor-level elements and key MEP

MODEL

LOD 200 Revit

ON SITE, FRAME BY FRAME

A beachfront store, recorded as the storm left it

Hurricane Ian hit the Surf Style building hard. Before anyone could design the repair, the engineer and architect needed to know what was still standing and where. Our crew scanned the interior so that record would be measured, not sketched.

Laser scanner on a tripod facing a storm-damaged turquoise storefront in Fort Myers Beach

01

The scanner set up in front of a storm-damaged storefront.

Scanner at an open storefront bay behind caution tape after Hurricane Ian

02

Open bays where the glazing used to be, taped off.

Scanner inside a gutted retail interior looking out to the street through the open front

03

Inside the shell, looking back out to the street.

Scanner under exposed ceiling structure and ductwork with storm debris behind it

04

Ceiling structure and ductwork, exposed and measurable.

Scanner beside an exposed block wall and timber framing inside the damaged building

05

Block wall and framing with the finishes gone.

Scanner positioned at a stripped entrance opening with the parking area beyond

06

A setup at an entrance opening to tie inside to outside.

Scanner on a sand-covered Fort Myers Beach street lined with storm-damaged buildings

07

The street outside, still covered in sand.

7 FRAMES · FORT MYERS BEACH · 2024

SCROLL SIDEWAYS →

Storm impact, on record

The scan captured the post-hurricane condition of the building for architectural and structural evaluation.

Sections that show the damage

Interior cross-sections revealed compromised framing, mechanical units and utility points.

The glazed front, modeled

The beachfront storefront was modeled to help the team plan a resilient redesign and access.

FROM THE CLIENT

Gilad Ovaknin

Manager at Surf Style Retail Management Inc.

“A great partner for our expansion projects.”

Thanks to ADS, we’ve been able to obtain accurate existing conditions documentation for our stores, a key starting point for our architects to begin the design and permitting process smoothly. They’ve supported us across multiple locations throughout Florida, and what stands out most is their speed, precision, and competitive pricing.

WHAT YOU CAN ORDER

The Surf Style set, line by line

The left column is what the Fort Myers Beach job produced. The next is what you can order for your own building. Each line is priced separately on the quote.

DELIVERABLE

01

Point cloud

AT THE SURF STYLE STORE

High-density point cloud of the interior.

FOR YOUR BUILDING

FILES

A registered 3D point cloud from our 3D laser scanning service.

E57

02

360° walkthrough

03

2D CAD drawings

Interactive walkthrough used for remote design coordination.

First floor plan, reflected ceiling plan and interior cross-sections.

A 360° digital twin you open in a browser.

Matterport

Floor plans, reflected ceiling plans, elevations and sections through as-built services.

DWG

PDF

04

Revit model

05

MEP and structure

LOD 200 model with wall layouts, ceiling slopes and system locations.

Framing elements and key MEP features shown in the 2D drawings.

A Revit model at LOD 200–300 from our BIM services team.

RVT

IFC

NWC

MEP documentation and structural elements where they are in scope.

DWG

RVT

06

Exterior and area

Facade conditions recorded in the 2D drawings.

Exterior elevations and roof plans when scoped (see building site plans), plus BOMA or REBNY area calculations from a building survey on request.

DWG

PDF

File formats delivered: DWG, PDF, RVT, IFC, NWC, E57 and a Matterport link. The files go to you and the consultants you name.

HOW IT RUNS

How a Fort Myers project runs

Most of the work happens after the scanner is packed away. One site visit gives us everything we need to draft the drawings and build the model.

Our only office is in Miami. Travel to Lee County is listed as its own line on the quote, so you can see exactly what it adds.

1

2

3

4

5

You send the basics

The address, approximate square footage and the deliverables you want.

We return an itemized quote

One line per deliverable, plus the travel line.

Scan day

A technician moves through the property with the scanner while it stays open.

Registration and drafting

The scans are registered into one point cloud. The drawings and model are drafted from it.

Review, then delivery

You review the set and request revisions before final delivery.

PERMITS AND REVIEW

Which desk your drawings land on

Your architect or engineer uses the as-built set as the existing-conditions base for the application. Where it is filed depends on which side of the city line the property sits.

INSIDE THE CITY

City of Fort Myers Community Development

The Building, Permitting & Inspections Division handles building permits inside the city limits. Applications go through the EnerGov portal. See the official permits page.

1825 Hendry St.
Fort Myers, FL 33901
239-321-7925

UNINCORPORATED COUNTY

Lee County Community Development

Properties in unincorporated Lee County are permitted by the county, not the city.

1500 Monroe St.
Fort Myers, FL 33901
239-533-8585

STATEWIDE RULE

Milestone inspections

Under Florida Statute 553.899, condominium and cooperative buildings three habitable stories or taller need a milestone structural inspection at 30 years (25 where the local authority requires it for buildings near salt water) and every ten years after.

F.S. 553.899

WHERE WE WORK

Downtown River District, McGregor, Fort Myers Beach, Cape Coral, Estero, Bonita Springs, Lehigh Acres, North Fort Myers, Sanibel and across Lee County.

QUESTIONS

Fort Myers questions, answered

Something else? Call 1-855-201-4043.

01

–

Do you document storm-damaged buildings in Fort Myers?

Yes. The Surf Style store on Fort Myers Beach was scanned after Hurricane Ian, and the interior sections showed the engineer where framing and mechanical systems were compromised. The same workflow applies to any building being assessed for repair or reconstruction.

01

–

Is it worth bringing ADS to Fort Myers from Miami?

For a full building, a storm-damaged structure or any job that needs both drawings and a model, yes: one visit produces everything. For a single small room the travel line may not be worth it, and we will tell you.

01

–

Where do permit drawings go in Fort Myers?

Inside the city limits they go to the City of Fort Myers Community Development Department at 1825 Hendry Street, with applications in the EnerGov portal. In unincorporated Lee County they go to Lee County Community Development at 1500 Monroe Street. Your architect or engineer uses the as-built set as the existing-conditions base.

01

–

How accurate are the drawings?

Dimensions are measured, not assumed, because every drawing is drafted from the registered point cloud. We scan with Leica RTC360 and BLK2GO scanners and the Matterport Pro3. Glazed storefronts, like the beachfront front of the Surf Style store, are handled by adjusting the scanner on site.

01

–

Does the store or office have to close during the scan?

No. Stores and offices stay open while we work, and after-hours visits can be arranged.

01

–

What sets the price of an as-built in Fort Myers?

Floor area, how much is in the space, the deliverables you want and travel set the price. Point cloud plus 2D CAD is the lowest tier, and a Revit model adds modeling time. MEP, exterior elevations and roof plans are added only when scoped. Every line is itemized.

Request an itemized quote

Send the property address, approximate square footage, the deliverables you need and your deadline. We reply with an itemized quote.

GET A QUOTE

Tell us about your Fort Myers property

Five details are enough to price it. Existing drawings, even old ones, help us scope faster.

1

Property address

2

Approximate square footage and number of floors

3

What it is for: renovation, storm repair, tenant improvement, insurance or facility records

4

Deliverables: point cloud, 2D CAD, Revit, MEP

5

Your deadline

PREFER TO TALK?

MEMBERSHIPS

ICSC member
Broward County Chamber of Commerce member
Chamber Approved A+
South Florida Women's Chamber of Commerce member

Reviewed by Antonio Tomecich

Founder & Director, As-Built Drawing Services.

Last reviewed November 2026.

bottom of page